Whitfield Igniter Element - Whitfield pellet stove parts

The Super Ignitor cartridge heaters run more efficiently, use less power and last up to 5 times longer than conventional heaters, with less downtime for heater replacements and lower maintenance costs. This igniter comes with a spare fuse and anti seize lubricant. The cost is a little more but the long term savings are great. Our customers love this product.

 Here is a link to the product on our site

Very Detailed instruction, fuse and thread lube are included.

Fits the following Whitfield Pellet Stoves:
Advantage II-T -WP2
Advantage III -WP2
Advantage II-T Classic -WP2 
Optima 2 FS
Optima 3 FS
Optima 3 INS 
Advantage Plus FS 
Profile 20 FS  Serial 7494 and lower
Profile 20 FS-2  Serial  7495 and above
Profile 30 FS Serial  11904 and above
Profile 30 FS-2  Serial  11905 and above 
Profile 30 INS  Serial  11904 and lower  
Profile 30 INS-2  Serial  11905 and ablove 
T300P -P11- T300P-T301P-T305P-T308P
Quest Plus FS -WP4
Quest Plus INS -WP4

Consult your manual and parts list available on our web site for confirmation on this and any parts.

This is a complete kit includes instructions, the Super Igniter, fuse and anti-seize.

Whitfield Pellet Stove Fireback

Whitfield Advantage II-T, III & II-T Classic - Fireback

$110.00  This is a 3 piece Premium FireTek^TM Fireback - Firebrick set
Dimensions - Sides - 5 7/16" wide x 12-3/4" Tall, Back 8 5/16" wide x 12 3/4" tall

This part is the ceramic fiber, brick appearance panel on the back wall of the firebox.

This part is designed to fit these models:

ADVANTAGE II , ADVANTAGE II-T MODEL YEARS: 1990 - 2000 (Serial # 18145 and up) Pellet, Freestanding and Insert, WP2
ADVANTAGE III MODEL YEARS: 1991 - 1996 (Serial # 18145 and up)
Advantage II-T Classic Pellet, Freestanding and Insert, WP2

Whitfield - Lennox Replacement Part Number 12146500

Beware that many fireboxes have warped over use and the fit may vary. This material can be cut with a table saw or sanded and shaved to fit the unique fit in your stove.

Pellet Stove Auger Motor Trouble Shooting

 Q>   My pellet stove is not feeding pellets.

I have a question about my Erin Waterford Renaissance pellet stove. It was working great until this spring when the auger motor stopped dropping pellets. The auger motor still has a sound, but not the turning sound. Would this only be a auger problem or is there something else I need to look at before I order a new auger. Thanks for your help Debra, La Center WA

A>    Response from Wood Heat - "Diagnose with deductive reasoning step by step"

Hi Debra,

I wish I could analyze all the possible reasons that your stove is not feeding pellets down the chute from your description but I am afraid that there are lots of possible reason and solutions and further examination would be necessary to avoid "throwing parts at the problem" which might not resolve it and create further frustration.

We cannot offer an analysis program thru email or over the phone but I will give you a few ideas to pursue and you or someone with some mechanical skills needs to dig in and evaluate what is occurring. I hope this helps. I have attached the guide to finding parts which can help you find the resources you will need and the parts list for the Renaissance pellet stove from Whitfield which is the same inner workings as the Waterford Erin. Some but not all of these parts are still available on this older model. Some of the parts can be rebuilt to repair those that are not available any longer.

Do you have a manual for the stove? Often troubleshooting symptoms is covered in these. There may be a technical manual that goes beyond the owner's manual. All of our manuals are listed in the category under documents.

Have you emptied the hopper to see if there is a pile of sawdust on the bottom? The auger cannot feed sawdust only clean pellets. This is the simplest solution and most common problem. Were pellets left in the stove over the summer? That is not advised since they can swell with moisture and make the auger seize up. Have you taken the back off of the stove to watch the auger movement? The auger on that model only runs for a few seconds then stops. Watching the auger to see if the motor is moving it during operation is the place to start. Removing the motor to run it under full power to see if you can hold it from moving with a vice grip pliers will tell you if the gear box in the motor case is stripped out. Removing the auger and clearing out jammed pellets turned to sawdust might be the solution.

See if these ideas lead to a conclusion or further questions. The factory technical department at Whitfield is available if they can talk to someone who is willing to go thru procedures like this and if necessary we can put you in touch with them once the more simple solutions are exhausted.

I hope this helps you get a clearer picture of what you are dealing with and the possible solutions.

Let us know if we can help you further in any way.

Thanks, Bruce

Bruce Beeley - owner

Nevada City, CA 95959

530-265-8618

Fax 530-265-8656

bruce@woodheatstoves.com

http://www.woodheatstoves.com/

Link to our blog @ http://blog.woodheatstoves.com/ 

Also to Facebook, MySpace & Twitter

Quadrafire Castile Feed Motor 101 pellet stove parts

CASTILE PELLET STOVE SERVICE  FEED MOTOR TROUBLE-SHOOTING

For a full list of Castile Parts, click HERE

for the service manuals, click Castile Insert    Castile FreeStanding

Pellet stove service can be dangerous and complicated, use this information safely

1) TURN ON THERMOSTAT CIRCUIT AND MAKE SURE THAT THE CALL LIGHT IS ON

2) CHECK FOR POWER AT THE VACUUM SWITCH:

A. IF NO POWER FROM RED WIRE-----CHECK CONTROL BOX OR WIRE HARNESS

B. POWER ON RED BUT NO POWER ON ORANGE-----CHECK VACUUM SWITCH OR VENT SYSTEM

3) CHECK FOR POWER AT THE ORANGE WIRE ON THE #2 SNAP DISC:

A. IF NO POWER FROM ORANGE WIRE----CHECK WIRE HARNESS OR RESET THE SNAP DISC

B. IF POWER IS PRESENT-----REPLACE FEED MOTOR OR CHECK CONNECTOR PIN OR CAPACITOR

NOTE: REMEMBER THAT THE FEED CIRCUIT INITIAL FEED TIME IS 60 SECONDS. PUSH THE RESET

BUTTON BEFORE EACH TEST.

CAPACITOR JUMPER WIRE. PART# 230-2150    

JUMPER IS NEEDED IFCAPACITOR IN J-BOX IS BAD OR IF THE

MOTOR NEEDS TO BE TESTED WITH A TEST CORD.

FEED MOTOR TESTING      USING THE TEST BOX:

1) UNPLUG THE STOVE, REMOVE THE CONTROL BOX, INSTALL TEST BOX W/ ADAPTER & PLUG IN STOVE

2) TURN ON THE EXHAUST BLOWER SWITCH. (THIS WILL PULL THE VACUUM SWITCH IN)

3) TURN ON THE THERMOSTAT (THE THERMOSTAT INDICATOR LIGHT SHOULD COME ON)

4) TURN ON THE FEED MOTOR SWITCH:

IF THE FEED DOESN'T COME ON: BAD FEED MOTOR, VACUUM SWITCH, OR #2 SNAP DISC

IF THE FEED COMES ON: REPLACE CONTROL BOX

USING THE COMPONENT TEST CORD:

1) UNPLUG THE FEED MOTOR FROM THE WIRE HARNESS

2) INSTALL THE FEED MOTOR ADAPTER ON THE TEST CORD

NOTE: THE NEW STYLE FEED MOTOR WILL NEED THE CAPACITOR JUMPER ADDED TO THE ADAPTER.

3) PLUG IN THE TEST CORD TO THE FEED MOTOR AND TURN ON THE SWITCH

Quad Mnt Vernon error codes, pellet stove service

Quadrafire Mnt Vernon AE error codes from service manual

This is the first of many articles to come on pellet stove repair!!

ERROR CODES
AUGER JAMMED: SEE PAGE 12 (FEED MOTOR TROUBLE-SHOOTING)

BAD TC DROP TUBE: SEE PAGE 10 (CONVECTION BLOWER TROUBLE-SHOOTING)

BAD TC FIRE POT: SEE PAGE 14 (FIREPOT, AUTOCLEAN & T-Couple TROUBLE-SHOOTING)

CHECK ASH PAN: SEE PAGE 13 (FIREPOT, AUTOCLEAN & T-Couple TROUBLE-SHOOTING)

COMB BLOWER JAMMED: SEE PAGE 11 (EXHAUST BLOWER TROUBLE-SHOOTING)

CONV BLOWER JAMMED: SEE PAGE 10 (CONVECTION BLOWER TROUBLE-SHOOTING)

MIN FP TEMP: UNIT IS OUT OF FUEL OR CHECK FOR PROPER FUEL SETTINGS. THIS CODE
WOULD DISPLAY ANYTIME THE FIRE GOT UNDER 500 DEGREES DURING ITS NORMAL RUN MODE.

MISSED IGNITION: UNIT IS OUT OF FUEL OR CHECK FOR PROPER FUEL SETTINGS. SEE
PAGE 14 (IGNITER TROUBLE-SHOOTING) THIS CODE WOULD DISPLAY IF THE FUEL DID NOT
LIGHT OR THE FIRE DID NOT GET HOT ENOUGH DURING START-UP AFTER 4 TRIES.

VACUUM SW ERROR: SEE PAGE 12 (FEED MOTOR TROUBLE-SHOOTING)

Pellet stove parts found here

We offer an astounding array of  pellet, wood, and gas stove parts Pellet Stove parts here this is the page to get started of if you are looking for pellet stove auger motors, ignitors, combustion blowers, firebacks, control boards, log sets, electrical parts, burn pots, gaskets,  free parts lists, manuals. Use our search box and enter the part number from our free parts list, or your owners manual to find your desired, diy, pellet stove parts. While our competitors are focused on only selling the high volume parts, we offer any and every part that is available, in shop technical support to help 877-265-8618 and very speedy replies to emails Info@woodheatstoves.com